For citation:
Zlobina I. V., Bekrenev N. V., Churikov D. O. Evaluation of the wettability of the filler binder during the manufacture of prepreg with ultrasound exposure for three-dimensional printing filaments reinforced with continuous carbon fiber. Izvestiya of Saratov University. Physics , 2024, vol. 24, iss. 1, pp. 52-61. DOI: 10.18500/1817-3020-2024-24-1-52-61, EDN: FNPWQU
Evaluation of the wettability of the filler binder during the manufacture of prepreg with ultrasound exposure for three-dimensional printing filaments reinforced with continuous carbon fiber
Background and Objectives: The aim of the research is to study the effect of ultrasound on the wettability of carbon fibers with a thermosetting binder and to determine the work of adhesion in the binder-fiber contact as part of the filament prepreg for additive technologies. Materials and Methods: Carbon fibers and carbon fiber roving with a width of 2 mm GG-200P were used in the research. Impregnation was carried out with ED-20 epoxy resin with a PEP hardener by pulling a harness at a speed of 10 mm/s through a gap of 2-3 mm between the end of the ultrasonic concentrator and the lower surface of the container with a binder. In total, 5 control and 5 experimental samples with a length of 300 mm were impregnated. Ultrasonic processing of samples was carried out on an experimental ultrasonic installation with an experimental ultrasonic generator controlled from a laptop and providing a discreteness of 10 Hz adjustment. The impregnation was carried out at a resonant frequency of 21650 Hz and an oscillation amplitude of the output end of the concentrator – 15 microns. The diameter of the output part of the concentrator was 14 mm, respectively, the length of the fiber bundle section was the same size at each time. After curing of the binder, the surface of the fibers was studied using a digital microscope Bresser LCD 50x–2000x at magnification x40 and x300. When impregnating control samples, the ultrasonic transducer of the installation was not included. Microphotographs were used to evaluate the wettability of the fibers with a binder under the influence of ultrasound and without ultrasound, and also to determine the edge angle of wetting and then – according to the Young – Dupree equation – the adhesion of the binder to the fiber surface. Results: The control bundle of carbon fibers is characterized by incomplete consolidation of fibers into a bundle, there are separate disoriented fibers, as well as separately existing conglomerates of fibers. Experimental bundles impregnated under the influence of ultrasound are monolithic structures with a continuous filling with a binder. At the same time, areas with inflows of the cured binder that violate the geometric shape of the prepreg are noted. Both control and experimental samples of harness are generally fully impregnated consolidated prepregs, there are no individual fibers or groups of fibers, which may be due to the initially regular structure of harness compared to randomly organized individual fibers into a thread. At the same time, in the control samples, the binder is unevenly distributed over the surface, individual inflows are noted, which indicates an insufficiently uniform impregnation of the harness. which is not observed on the prototypes. By calculating the adhesion performance for control and experimental samples using the experimentally obtained values of the wetting angle, it was found that its value is 44.71–48.98 mJ/m2 and 64.46–66.4 mJ/m2 , respectively, for control and experimental samples. Conclusion: A significant improvement in the wettability of the fibers with a binder has been found, manifested in a decrease in the wetting edge angle from 70–77° to 35–40°. Using the Young – Dupree equation, the adhesion of the binder to the fiber has been calculated and it has been shown that the effect of ultrasound during the impregnation of fibers increases the adhesion by an average of 39.7%
- Gibson Ya., Rosen D., Stocker B. Tekhnologii additivnogo proizvodstva. Trekhmernaia pechat’, bystroe prototipirovanie i pryamoe tsifrovoe proizvodstvo [Additive manufacturing technologies. Three-dimensional printing, rapid prototyping and direct digital production]. Moscow, TECHNOSPHERE, 2016. 656 p. (in Russian).
- Bikas H., Stavropoulos P., Chryssolouris G. Additive Manufacturing methods and modeling approaches: A critical review. International Journal of Advanced Manufacturing Technology, 2016, vol. 83, pp. 389–405. https://doi.org/10.1007/s00170-015-7576-2
- Mikhailin Yu. A. Spetsial’nye polimernye kompozitsionnye materialy [Special polymer composite materials]. St. Petersburg, Nauchnye osnovy i tekhnologii, 2008. 660 p. (in Russian).
- Mikhailin Yu. A. Konstruktsionnye polimernye kompozitsionnye materialy. 2-е izd. [Structural polymer composite materials. 2nd ed.]. St. Petersburg, Nauchnye osnovy i tekhnologii, 2010. 822 p. (in Russian).
- Balashov A. V., Markova M. I. Investigation of the structure and properties of products obtained by 3D printing. Engineering Bulletin of the Don, 2019, no. 1 (52), pp. 66. (in Russian).
- Petrov V. M., Bezpalchuk S. N., Yakovlev S. P. On the influence of structure on the strength of plastic products obtained by 3D printing. Bulletin of the Admiral S. O. Makarov State University of the Sea and River Fleet, 2017, vol. 9, no. 4, pp. 765–776 (in Russian). https://doi.org/10.21821/2309-5180-2017-9-4-765-776
- Matsuzaki R., Ueda M., Namiki M., Jeong T. K., Asahara H., Horiguchi K., Nakamura T., Todoroki A., Hirano Y. Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation. Sci Rep., 2016, article no. 23058. https://doi.org/10.1038/srep23058
- Ning F., Cong W., Qiu J., Wei J., Wang S. Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling. Composites Part B-engineering, 2015, vol. 80, pp. 369–378. https://doi.org/10.1016/j.compositesb.2015.06.013
- Invernizzi M, Natale G, Levi M, Turri S, Griffini G. UV-Assisted 3D Printing of Glass and Carbon Fiber-Reinforced Dual-Cure Polymer Composites. Materials, 2016, vol. 9, iss. 7, pp. 583. https://doi.org/10.3390/ma9070583
- Polyzos E., Katalagarianakis A., Hemelrijck D. Van, Pyl L., Polyzos D. A. Multi Scale Analytical Methodology for the Prediction of Mechanical Properties of 3D-printed Materials with continouos Fibres. Additive Manufacturing, 2020, vol. 36, article no. 101394. https://doi.org/10.1016/j.addma.2020.101394
- Wang F., Wang G., Zhang Z., Ning F. Fiber-matrix Impregnation Behavior During Additive Manufacturing of continouos Carbon Fiber reinforced Polylactic Acid Composites. Additive Manufacturing, 2021, vol. 37, article no. 101661. https://doi.org/10.1016/j.addma.2020.101661
- Kuleznev V. S., Shershnev A. S. Khimicheskaia i fizicheskaia modifikatsiia polimerov [Chemical and physical modification of polymers]. Moscow, Khimiya, 1990. 207 p. (in Russian).
- Studentsov V. N. Physical modification of reinforced reactoplasts. Vestnik Saratov State Technical University, 2011, no. 4, iss. 3, pp. 209–218 (in Russian).
- Negrov D. A. The influence of the energy of ultrasonic vibrations on the structure and properties of a polymer composite material based on polytetrafluoroethylene. Thesis Diss. Cand. Sci. (Tech.). Omsk, 2009. 123 p. (in Russian).
- Khozin V. G., Karimov A. A., Cherevatsky A. M., Polyansky A. A., Murafa A. V. Modification of epoxy compositions by ultrasound. Mekhanika kompozitsionnykh materialov, 1984, no. 4, pp. 702–706 (in Russian).
- Khmelev V. N., Bashara V. A., Nikitin A. A., Tsyganok S. N., Barsukov R. V. Creation of an ultrasonic device for impregnating products from composite polymer materials. Kompozity – v narodnoe khozyaistvo Rossii» (Kompozit ’99): sbornik mezhdunarodnoi nauchno-tekhnicheskoi konferentsii: tezisy dokladov [Composites – in the national economy of Russia (Composite ‘99): Collection of abstracts of the international scientific and practical conference]. Barnaul, Polzunov Altai State Technical University Publ., 1999, pp. 42–43 (in Russian).
- Khmelev V. N., Barsukov R. V., Tsyganok S. N., Slivin A. N., Khmelev M. V. Polzunov Altai State Technical University. Device for ultrasonic impregnation, RU No. 2224649, MPK V29V 15/10, 2004 (in Russian).
- Volkov S. S., Bigus G. A., Remizov A. L. Technology and equipment for ultrasonic welding of polymer composite materials. Plasticheskie massy [Plastic Masses], 2018, no. 5-6, pp. 50–55 (in Russian). https://doi.org/10.35164/0554-2901-2018-5-6-50-55
- Khmelev V. N., Khmelev S. S., Tsyganok S. N., Titov G. A. Ul’trazvukovaia propitka polimernykh kompozitsionnykh materialov [Ultrasonic impregnation of polymer composite materials]. South-Siberian Scientific Bulletin, 2012, no. 2, pp. 193–196. (in Russian).
- Khmelev V. N., Khmelev S. S., Kazakova K. A., Golykh R. N. Improving the efficiency of ultrasonic exposure in the production of highly filled composite materials. South-Siberian Scientific Bulletin, 2012, no. 2, pp. 189–192 (in Russian).
- Khmelev V. N., Khmelev S. S., Tsyganok S. N., Titov G. A. The Ultrasonic Impregnation of Polymer Composite Materials. Inernational Workshop and Tutorias on Electron Devices and Materials, EDM. Proceedings, 2012, pp. 170–173.
- Lionetto F., Dell’Anna R., Montagna F., Maffezzoli A. Ultrasonic Assisted Consolidation of Commingled Thermoplastic/Glass Fiber Rovings. Front. Mater., 2015, vol. 2, pp. 32. https://doi.org/10.3389/fmats.2015.00032
- Smirnov S. V., Veretennikova I. A., Konovalov D. A., Michurov N. S., Osipova V. A., Pestov A. V. Effect of hardeners on the mechanical properties of epoxy coatings based on ED-2 resin. Diagnostics, Resource and Mechanics of Materials and Structures, 2023, iss. 1, pp. 6–16. https://doi.org/10.17804/2410-9908.2023.1.006-016
- Nushtaeva A. V., Melnikova K. S., Prosvirnina K. M., Nushtaeva S. A. Contact angle measurements by sessile-drop technique on a vertical surface. Fundamental Research, 2015, no. 2-13, pp. 2855–2859 (in Russian).
- Bogdanova Yu. G. Adgeziia i ee rol’ v obespechenii prochnosti polimernykh kompozitov: uchebnoe posobie [Adhesion and its role in ensuring the strength of polymer composites. Textbook]. Moscow, Lomonosov Moscow State University Publ., 2010. 68 p. (in Russian).
- Berlin A. A. Polimernye kompozitsionnye materialy: struktura, svoistva, tekhnologiia [Polymer composite materials: Structure, properties, technology]. St. Petersburg, Professiya, 2009. 556 p. (in Russian).
- Bogdanova S. A., Slobozhaninova M. V., Vashurin S. A., Deberdeev R. Ya., Barabanov V. P. Spreading of epoxy resin and polyester on the surface of substrates with different polarity. Struktura i dinamika molekuliarnykh sistem. Ial’chik-2002: sbornik statei [Structure and Dynamics of Molecular Systems. Yalchik-2002: Coll. of arts.]. Yoshkar-Ola, MarGTU Publ., 2002, pp. 60–63 (in Russian).
- Antipov Yu. V., Kruglov E. V., Pakhomov K. S., Chalykh A. E. Influence of plasma flow of high-frequency capacitive discharge of reduced pressure on adhesive and physico-mechanical characteristics of aramid and carbon fibers. Plasticheskie massy [Plastic Masses], 2021, no. 9–10, pp. 8–11 (in Russian). https://doi.org/10.35164/0554-2901-2021-9-10-8-11
- Fizika i tekhnika moshchnogo ul’trazvuka: v 3 kn. AN SSSR. Akusticheskii institut; pod red. L. D. Rozenberga. Kn. 3: Fizicheskie osnovy ul’trazvukovoi tekhnologii [Rosenberg L. D., ed. Physics and technology of powerful ultrasound: in 3 books. Book 3: Physical foundations of ultrasonic technology]. Moscow, Nauka, 1970. 689 p. (in Russian).
- Rozina E. Yu. Cavitation mode of the sound capillary effect. Akustichnyi visnyk, 2003, vol. 6, no. 1, pp. 48–59 (in Russian).
- 508 reads