For citation:
Gorshkov I. B., Petrov V. V. Numerical Simulation of a Looped Tube 4-Stage Traveling-Wave Thermoacoustic Engine. Izvestiya of Saratov University. Physics , 2018, vol. 18, iss. 4, pp. 285-296. DOI: 10.18500/1817-3020-2018-18-4-285-296
Numerical Simulation of a Looped Tube 4-Stage Traveling-Wave Thermoacoustic Engine
Background and Objectives: The technology of thermoacoustic energy conversion is one of the most promising technologies for converting thermal energy into electrical one. A brief review of the achievements in development of the multi-stage traveling-wave engines was made. The numerical simulation of a 4-stage engine with a load was done. The aim of research was to determine the engine parameters, required to achieve the maximum of efficiency of the system and the acoustic power on the load. Materials and Methods: Optimization of the engine parameters was carried out in the DeltaEC program. This program numerically integrates differential equations of thermoacoustics. The calculation procedure and the features of the calculation of a 4-stage engine are described. For the calculation the engine was taken with a looped tube resonator having the length 6 m and a 33 mm diameter of the stage. The temperature of the hot and cold heat exchangers in all calculations was 600 K and 300 K, respectively. The working gas is helium with a pressure of 1 MPa. Results: It has been shown that by sacrificing efficiency on the load, it is possible to significantly increase the output power on the load (about 24.5 times). When the system was tuned to the maximum power on the load, then the calculated efficiency at the load occurred 3.44 times less than that in the case of the system setting to the maximum efficiency of the system with the load. The optimal position of the load inside the resonator, the optimal ratio of the diameter of the stage and the diameter of the resonator were determined for the engine specified in the calculation. Recommendations for choosing the length of the stage are given. The optimum value of the hydraulic radius for heat exchangers and for the regenerator is one order of magnitude. Conclusion: The obtained results can be used to design 4-stage traveling-wave thermoacoustic engines.
1. Reader G., Hooper C. Stirling engines. London, E. & F. N. Spon, 1986. 462 p.
2. Jingyuan X., Guoyao Y., Limin Z., Wei D., Ercang L. Theoretical analysis of two coupling modes of a 300-Hz three-stage thermoacoustically driven cryocooler system at liquid nitrogen temperature range. Appl. Energ., 2016, vol. 185, pp. 2134–2141. DOI: https://doi.org/10.1016/j.apenergy.2016.04.055
3. Dovgiallo A. I., Shimanov A. A. Possibility of using a bidirectional impulse turbine in a thermo-acoustic engine. Vestnik SGAU [Vestnik of the Samara State Aero-space University], 2015, vol. 14, no. 1, pp. 132–138 (in Russian). DOI: https://doi.org/10.18287/1998-6629-2015-14-1-132-138
4. Swift G. W. Thermoacoustic engines and refrigerators: a short course. Los Alamos, Los Alamos National Laboratory, 1999. 179 p. Available at: https://www.osti.gov/servlets/purl/756947 (accessed 20 August 2018).
5. Jin T., Yang R., Wang Y., Feng Y., Tang K. Low temperature difference thermoacoustic prime mover with asymmetric multistage loop confi guration. Sci. Rep. UK, 2017, vol. 7, pp. 1–8. DOI: https://doi.org/10.1038/s41598-017-08124-5
6. Zhanghua W., Wei D., Man M., Ercang L. A solar-powered traveling-wave thermoacoustic electricity generator. Sol. Energy, 2012, vol. 86, pp. 2376–2382. DOI: https://doi.org/10.1016/j.solener.2012.05.010
7. Yang R., Wang Y., Jin T., Feng Y., Tang K. Development of a three-stage looped thermoacoustic electric generator capable of utilizing heat source below 120 °C. Energ. Convers. Manage, 2018, vol. 155, pp. 161–168. DOI: https://doi.org/10.1016/j.enconman.2017.10.084
8. Yu Z., Jaworski A., Backhaus S. Travelling-wave thermoacoustic electricity generator using an ultra-compliant alternator for utilization of low-grade thermal energy. Appl. Energ., 2012, vol. 99, pp. 135–145. DOI: https://doi.org/10.1016/j.apenergy.2012.04.046
9. Ceperley P. H. A pistonless Stirling engine – the traveling wave heat engine. J. Acoust. Soc. Am., 1979, vol. 66, no. 5, pp. 1508–1513. DOI: https://doi.org/10.1121/1.383505
10. Aster Thermoacoustics. Available at: http://www.aster-thermoacoustics.com/wp-content/uploads/2015/01/Presenta... (accessed 20 August 2018).
11. Blok K. Novel 4-stage traveling wave thermoacoustic power generator. Proceedings of ASME 2010 3rd joint US-European fl uids engineering summer meeting and 8th international conference on nanochannels, microchannels, and minichannels. FEDSM-ICNMM2010, August 1–5, 2010. Monreal, Canada, 2010, pp. 73–79. DOI: https://doi.org/10.1115/FEDSM-ICNMM2010-30527
12. Kruse A., Ruziewicz A., Tajmar M., Gnutek Z. A numerical study of a looped-tube thermoacoustic engine with a single-stage for utilization of low-grade heat. Energ. Convers. Manage, 2017, vol. 149, pp. 206–218. DOI: https://doi.org/10.1016/j.enconman.2017.07.010
13. Wang K., Qiu L. Numerical analysis on a four-stage looped thermoacoustic Stirling power generator for low temperature waste heat. Energ. Convers. Manage, 2017, vol. 150, pp. 830–837. DOI: https://doi.org/10.1016/j.enconman.2017.03.023
14. Ward B., Clark G., Swift G. Design environment for low-amplitude thermoacoustic energy conversion, version 6.3b11, users guide. Los Alamos, Los Alamos National Laboratory, 2012. 288 p. Available at: http://www.lanl.gov/org/padste/adeps/materials-physics-applications/cond... (accessed 20 August 2018).
15. Piccolo A., Pistone G. Estimation of heat transfer coeffi cients in oscillating fl ows: the thermoacoustic case. Int. J. Heat Mass Tran., 2006, vol. 49, pp. 1631–1642. DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2005.11.009
16. Abduljalil A. S., Yu Z., Jaworski A. J. Selection and experimental evaluation of low-cost porous materials for regenerator applications in thermoacoustic engines. Mater. Design, 2011, vol. 32, pp. 217–228. DOI: https://doi.org/10.1016/j.matdes.2010.06.012
17. Organ A. J. Thermodynamics and gas dynamics of the Stirling cycle machine. Cambridge, Cambridge University Press, 1992. 414 p.
18. Yu Z., Jaworski A. J. Impact of acoustic impedance and fl ow resistance on the power output capacity of the regenerators in travelling-wave thermoacoustic engines. Energ. Convers. Manage, 2010, vol. 51, pp. 350–359. DOI: https://doi.org/10.1016/j.enconman.2009.09.032
- 1589 reads